Where is the controller on this Walmart ebike?

[anshaffer]

Hello, I recently purchased this ebike to replace a different stolen cheaper 36V ebike. That one had readily accessible components to modify, and I assumed this one would as well. Instead, as I poke around the bike I somehow cannot locate the controller. There is internally routing of wires and cables, and they are visible when I fold the bike down the center + also at the very bottom (where I'd assume they link to a controller that I cannot find.

Here's a picture of the bike, and I'd appreciate any thoughts on how I might access this! I don't need to make a lot of modifications, but it doesn't come with a rear bike light and I'd possibly like to upgrade the battery (which I assume will require a new mount).

Thank you all for any help you can offer!

 

[harryS]

If you can't find it in the frame, it's probably inside the battery cradle.

 

[PedalUma]

follow a wire and it will lead to the controller. It is the junction box for all functions, with the motherboard and more.

 

[fexixav]

Hello, I recently purchased this ebike to replace a different stolen cheaper 36V ebike. That one had readily accessible components to modify, and I assumed this one would as well. Instead, as I poke around the bike I somehow cannot locate the controller. There is internally routing of wires and cables, and they are visible when I fold the bike down the center + also at the very bottom (where I'd assume they link to a controller that I cannot find.

Here's a picture of the bike, and I'd appreciate any thoughts on how I might access this! I don't need to make a lot of modifications, but it doesn't come with a rear bike light and I'd possibly like to upgrade the battery (which I assume will require a new mount). espaço invisível ff 2025

Thank you all for any help you can offer!

Ordered a pair of these 2 days ago. Bikes havent arrived yet and already I want to make DIY changes. I seek your wisdom!

Its the Hyper e-ride mountain bike. 36v 7.8ah 250w rear hub.

Lets change to a controller that will: give me integrated lights, a twist throttle, a decent display. This bike stock has none of those features.

If the battery will allow, Id like to pump more power to that 250w hub - use as a 500w at least, but I need your opinions. I wont know if thats possible until its delivered and I can get the battery out to put on my multimeter and post images here.

I have a good soldering station, crimpers, multimeter etc.

I bought these bikes to get into the DIY aspect of the ebike hobby.

 

[harryS]

Its the Hyper e-ride mountain bike. 36v 7.8ah 250w rear hub.

Lets change to a controller that will: give me integrated lights, a twist throttle, a decent display. This bike stock has none of those features.

This reddit thread says you can solder a throttle to three terminals on the hyper circuit board. Read down to the bottom.

Or you could just put in a different controller, which will cost you about $100 up, A 20A KT controller might give you a better feel on the pedal assist, Their color displays are hard to see in sunlight, They support lights but you should use a relay after the light output as it's low current.

 

[PedalUma]

Wire gauges from the factory are based on specification power anticipations. You will burn wires top to bottom if exceeding them. One variable change impacts all others. You can't just overclock a chip on a slower PC. It all works together, as originally planned. Wires and connectors will be fired before three weeks. Make one part more robust, then make all system components match. Being inquisitive is very good. As are customizations. Systems have limitations. A 250 nominal motor is built and set for that. It is easy to void a warrantee and end with unsellable junk that is only good for a sea anchor. Firstly buy a bike that has the specifications you want to end with. Or, design your own, so it all works together as an integrated system. The discharge wire from a 60 battery is so much larger, for example, than the wire from a 36V. I am all for DYI.

 

[anshaffer]

If you can't find it in the frame, it's probably inside the battery cradle.
View attachment 192146

Thanks for this! I'd started to develop a theory that this was the case, but it didn't seem any thicker than my existing ebike's battery cradle so I dismissed and figured it was tucket into some nook or cranny somewhere. Am I right in looking into these that one of these 3 wires coming out of this example picture you shared is a julet that likely has a splitter to power/control things like the display, lights, etc?

 

[harryS]

Undocumented plugs for lights have blown out the 5 volt supplies of controllers, Test/verify the pins work as expected before you use it. A relay is advised.

If it doesn't already have a display or handlebar unit, you're not likely to be able to add one.