I'm 6'-0.4" I think in your units. 35" should be around 89cm? This would be my inseam as well. I'm between L and XL, but as top and seat tube are quite low on the Creo as you said I preferred XL with my inseam. But the 110mm stem was to long for me, I changed it to 90mm.
Specialized Turbo Creo 28mph Electric Road Bike
- Thread starter Admin
- Start date
Replaced the Dropper post with a Redshift Rock-shot suspension seat post and rode 50 miles and it is a great product, very comfortable
You need to make sure you are in the right gear to avoid bounce when putting a lot of effort into peddling, otherwise it is fine
With the new satellite power adjusters that sit on your handlebar in conjunction with a Planet 3 assist this is truly a great bike
I have ridden 8000 miles in a year and just love it. It is a lot of money, but is great value if you use it a lot
I recently purchased a new Mavic Carbon front wheel for snow tyres (Had a spare rear wheel already) and did not realise that the front fork was 110mm and road wheels are 100mm. After a fair amount of investigation I came across a "Boost" system that enables you to marry the two together. The Boost coverts the disc from Center Lock to 6 pin and you then have to introduce 2 x 5mm spacers, and works great
The total cost was £290 which was great value as you can only purchase the original Roval C38 in pairs @ over £1,000
It is difficult to get a direct 110mm replacement as the Creo is 12mm axle and most 110mm wheels are 15mm axle
After I went through the exercise I found out that Strada Wheels can build what you want for around £260 on aluminium or £530 for carbon
The guy I spoke to at Strada; Darren was very helpful 01903214956
You need to make sure you are in the right gear to avoid bounce when putting a lot of effort into peddling, otherwise it is fine
With the new satellite power adjusters that sit on your handlebar in conjunction with a Planet 3 assist this is truly a great bike
I have ridden 8000 miles in a year and just love it. It is a lot of money, but is great value if you use it a lot
I recently purchased a new Mavic Carbon front wheel for snow tyres (Had a spare rear wheel already) and did not realise that the front fork was 110mm and road wheels are 100mm. After a fair amount of investigation I came across a "Boost" system that enables you to marry the two together. The Boost coverts the disc from Center Lock to 6 pin and you then have to introduce 2 x 5mm spacers, and works great
The total cost was £290 which was great value as you can only purchase the original Roval C38 in pairs @ over £1,000
It is difficult to get a direct 110mm replacement as the Creo is 12mm axle and most 110mm wheels are 15mm axle
After I went through the exercise I found out that Strada Wheels can build what you want for around £260 on aluminium or £530 for carbon
The guy I spoke to at Strada; Darren was very helpful 01903214956
Captain Slow
Well-Known Member
I bought a MTB front wheel that is 110 x 15 and got MTB tools to make a part that fits inside the axle to reduce the diameter from 15 mm to 12 mm. I think it was about $25 US.
Necessity is the mother of invention along with the cliche: There is more than one way to crack an egg
abercrombie
Member
Any ideas on my chainring having a little give when rocking back and forth? Tight bolts for the spider, and also tight for the 1 little bolt between the chain ring and spider.
When I ride over bumps, the area rattles.
When I ride over bumps, the area rattles.
e-levity
Active Member
@abercrombie - that's definitely not normal! Which model is it?
We have two Creo Comp Carbon EVOs (Praxis cranks) that have seen a lot of rough trail miles, and the chainrings remain rock solid.
I can't tell from your video, does the spider move on the shaft?
Or, do the spindle and crank arm move with the ring and spider?
Have you removed the crank arm and/or spider to better see exactly where the slop is?
And of course, do you have a shop nearby???
We have two Creo Comp Carbon EVOs (Praxis cranks) that have seen a lot of rough trail miles, and the chainrings remain rock solid.
I can't tell from your video, does the spider move on the shaft?
Or, do the spindle and crank arm move with the ring and spider?
Have you removed the crank arm and/or spider to better see exactly where the slop is?
And of course, do you have a shop nearby???
taylorpetie
Member
There is a lock ring that holds the spider arm in place. If it’s not seated properly there will be lateral movement. Took me awhile to figure that out. I took it to LBS and all they did was slapped a bunch of grease to remove the noisebut there was still lateral movement.
Remove the lock ring, push the spider arm against the spindle and reinstall the lock ring. Make sure the lock ring is seated flat.
Hello everyone! First post here... I read this entire thread within the past couple weeks as I researched the decision between a Turbo Levo SL and a Creo SL. First and foremost, I want to give a big thanks to everyone who contributed to this discussion. It really helped me make my decision.
My desire to find a trail capable bike is what got me researching a purchase in the first place. For the past decade or so, I've been exclusively a road cyclist, mainly for exercise and touring but also for commuting. My current road bike is a Cannondale Synapse. My last mtn bike was retired many years ago, a '97 hardtail aluminum StumpJumper (Comp M2) that was my all time favorite bike... Until now. I used to put slicks on that bike to ride it on roads more efficiently and make it a bit of a hybrid, do it all bike. This Creo basically achieves that goal more effectively and adds pedal assist. It's a bit of a dream bike really.
I joined the club this week and had my LBS order one of the last few Comp Carbons in my size (M) from Specialized. The Mediums are sold out online now. I could have stepped up to the Expert as there seem to be plenty Mediums left in the Forest Green (which looks gorgeous), but after tax it would have been nearly an extra $3,000 USD. I thought about it, but I would have had to finance a portion of the purchase and I didn't want to go that route if I could help it. Plus I'm not sure the extra coin is worth it for the carbon wheels and Di2 if I plan to do a lot of gravel and light single track riding.
So here she is, my Creo SL Comp Carbon Evo:
Besides coming here to share and to give a big shout out to everyone who contributed to this thread, I wanted to ask a very important question:
Is the warranty still 4 years for the motor and battery? I read in this thread that Specialized had extended that warranty from 2 to 4 years for Turbo components, but I couldn't find any documentation and I'm not sure if that is still the case or if that was back when they were having more issues. Can someone confirm and share something I can reference just in case I need it?
Cheers!
My desire to find a trail capable bike is what got me researching a purchase in the first place. For the past decade or so, I've been exclusively a road cyclist, mainly for exercise and touring but also for commuting. My current road bike is a Cannondale Synapse. My last mtn bike was retired many years ago, a '97 hardtail aluminum StumpJumper (Comp M2) that was my all time favorite bike... Until now. I used to put slicks on that bike to ride it on roads more efficiently and make it a bit of a hybrid, do it all bike. This Creo basically achieves that goal more effectively and adds pedal assist. It's a bit of a dream bike really.
I joined the club this week and had my LBS order one of the last few Comp Carbons in my size (M) from Specialized. The Mediums are sold out online now. I could have stepped up to the Expert as there seem to be plenty Mediums left in the Forest Green (which looks gorgeous), but after tax it would have been nearly an extra $3,000 USD. I thought about it, but I would have had to finance a portion of the purchase and I didn't want to go that route if I could help it. Plus I'm not sure the extra coin is worth it for the carbon wheels and Di2 if I plan to do a lot of gravel and light single track riding.
So here she is, my Creo SL Comp Carbon Evo:
Besides coming here to share and to give a big shout out to everyone who contributed to this thread, I wanted to ask a very important question:
Is the warranty still 4 years for the motor and battery? I read in this thread that Specialized had extended that warranty from 2 to 4 years for Turbo components, but I couldn't find any documentation and I'm not sure if that is still the case or if that was back when they were having more issues. Can someone confirm and share something I can reference just in case I need it?
Cheers!
Last edited:
What a terrible choice, I would never ever choose a Creo in that colour! ;-)
To the warranty question: For Germany there was an announcement last august, that the warranty will be extended to 4 yours for all 2019-2020 Turbo Levo and Turbo Kenevo. So not for SL models.
But if I understood correct, the extension was to due some problems 2019+2020 with these Turbo models, which are fixed in the 2021 models. So no extended 4 year warranty for 2021 models or in general. And seems the extension was no kind of goodie or "We believe so much in our Turbo models...". More to give the customers who bought a 2019 or 2020 Turbo model the safety, if they encounter one of these flaws after more than 2 years, that Specialized will cover it. And Specialized avoids a general recall of all Turbos models of these two years.
So maybe no reason to wish such a warranty extension also for SL models, if it comes along with general defects/flaws...
To the warranty question: For Germany there was an announcement last august, that the warranty will be extended to 4 yours for all 2019-2020 Turbo Levo and Turbo Kenevo. So not for SL models.
But if I understood correct, the extension was to due some problems 2019+2020 with these Turbo models, which are fixed in the 2021 models. So no extended 4 year warranty for 2021 models or in general. And seems the extension was no kind of goodie or "We believe so much in our Turbo models...". More to give the customers who bought a 2019 or 2020 Turbo model the safety, if they encounter one of these flaws after more than 2 years, that Specialized will cover it. And Specialized avoids a general recall of all Turbos models of these two years.
So maybe no reason to wish such a warranty extension also for SL models, if it comes along with general defects/flaws...
I see, thanks for the info!
I was about to ask what color you had and then realized you were being sarcastic. I remember the pics of your bike from researching this thread.
I like how understated the satin sage can be in certain lighting. It's not trying to be flashy at all, yet in direct sunlight still pops. Dig the green and black motif it has going.
You probably ordered the last one available. Nice choice! I have zero complaints after a weekend of ownership.
However, I am going to ask my LBS about the road remote (I thought all new models were supposed to come with it at this point, but I didn't get one, maybe because they are backordered) and chainguide.
I got my Creo CC EVO in mid January. At that time, the remote buttons were in stock and the LBS installed them while doing the initial build up of my bike. Last week the chain guide was installed. It arrived from the factory in less than a week. Mine is blue. If I'd have seen the green in the flesh, I probably would have gone with that color.....Enjoy your ride.
Ironic is the word... In my native language I would have left out also the twinker smiley. But I'm to unsure about irony in English, in general I have the impression that it's less common (or maybe just in english forums).
I also like the understatement look. And I don't care for a nice glittering look for a heavily used item like my bikes. Also I find the colour very suited for an EVO/gravel bike. Looks like you came right out of the forest, even if it was only the bike shop half a mile behind you... ;-)
Kenmaryj
New Member
- Region
- USA
Greetings. First post. Thank you all for the discussion of the Creo. Been researching. Taken me a week or two to get through the 38 pages. Skimmed parts that were more in the weeds than I needed. Have test ridden Comp Carbon, Comp Carbon EVO, and E5 in XL. Leaning towards EVO, though not sure I need the drop seat post or flared bars. However, I do like the sage green. I am 6', long torso, short legs. Took up road biking in 2009 with a Roubaix. Rode for 5 years or so, then got busy with other stuff. I'm heavy. I want to get back into cycling. Neck hurts after test riding Creo. Not sure if it's because I haven't been riding in a while, or due to the more aggressive geometry compared to the Roubaix. Very interested in the modifications that could be made to the stem. Saw the comments on this aspect in this thread and the reference to the other thread. RMK, looks as if your setup has raised the handlebars quite a bit. I should go back and read the posts carefully to see what to suggest to my LBS, as they are not sure what else they can do besides flip the stem. They also don't normally try modifications to the bike before it's sold. I had them take some measurements on Roubaix and Creo. Seems as if I need at least 1.5 inches more height on the stem to get seat and handlebar relationship similar. I'm in the California South Central Coast area. Which other threads are good for general Creo SL discussions? Thanks all. Love the kindness and courtesy shown here. Respectful, humble, tolerant, etc.
Last edited:
mschwett
Well-Known Member
- Region
- USA
hi ken. i’m new to road bikes, and recently got a turbo creo comp carbon in XL. i’m 6’2. probably because i’m new to it, i was very uncomfortable with how low the bars were, so my local shop (before I bought it!) put on a shorter, much more angled stem and flipped it up. no charge. i’m a few hundred miles in now, and might eventually go back to something more aggressive, but i feel super comfortable on it now.
Similar threads
