XT60-to-ST3 cable adapter

[Kdlnet]

I'm having a difficult time finding a cable with XT60 female on one end and what I think its an ST3 male plug for a new battery charger. I appreciate your help people
Picture attached

 

[Gionnirocket]

I'm having a difficult time finding a cable with XT60 female on one end and what I think its an ST3 male plug for a new battery charger. I appreciate your help people
Picture attached

With almost certainty you'll have to fabricate one yourself... or find someone who will.

That said.. Perhaps inquire with... GRIN

Also that doesn't look like a standard ST3

 

[Gionnirocket]

One alternative that I've done in similar situations is to cut the connector off each charger somewhere in the wire legnth (I prefer close to the charger with about 6" of wire on that side ) and crimped barrel connectors on all ends so I can plug them in as needed. Just be mindful of polarity and use different genders for each so it can't be plugged in backwards.

Here both chargers used female for positive and male for negative. Then did the opposite on the connector side.
If you want to make it semi_permanent... Once connected you can put a piece of heat shrink over the connections so they can't be pulled apart.
This is fast, easy, requires no soldering and is very secure when done correctly.
You can also use a spade or any other type of crimp on connector you may have. I find barrel go together and come apart easily while still being secure.

 

[fauconnier]

People who fly remote-controlled model airplanes or helicopters are very comfortable with XT-60 soldering. There is almost certainly a club in your area.

 

[Gionnirocket]

People who fly remote-controlled model airplanes or helicopters are very comfortable with XT-60 soldering. There is almost certainly a club in your area.

I've soldered XT60 connectors and tho not for the amateur to attempt... that's really not the issue.
It's the inability to find the so called ST3 connector.. and then the necessity of a soldered connection in this situation.

 

[6zfshdb]

That is definitely not an ST3 connector. It's likely proprietary. It's a common practice with some bike makers.
An ST3 looks like the one shown here and above, and has a pinout like this:

I'm not sure why you want to replace your charger, but if it's defective, as Gionnirocket says above, you can cut the connector off and wire it directly to the new charger, or an XT60 connector. Make sure to check the wiring for the correct polarity.

Here's a link to the Grin connector tutorial, it may be of some help:

Ebike Connector Types: Anderson, JST, XT60 & Pinouts

A guide to the connectors used on ebikes: Anderson Powerpole, JST-SM, Higo, XT60 and XT90, XLR, and the other power, signal, and charger plugs you'll run into. There is no real standardization across the industry, so we standardized our kits on a minimal, well-chosen set. This page explains the...

ebikes.ca

Posting the make & model of the battery & charger might help others provide a solution.

Welcome to the forum, and good luck with your project.

 

[boatworksjon]

 

[Gionnirocket]

View attachment 217358

NIce!!
That's half the battle.... Do you happen to know where to buy one with an XT60 ?
A quick Google found this... which I guess could be cobbled to an xt60

JUNLEI 3015 3-Pin E-Bike Charging Adapter | Linkteller

DC5521 to JUNLEI 3015 3-pin charging adapter for select Lectric XP4, XPedition 2.0, XPeak 2.0, XPress2 and Schwinn e-bikes. Compact, durable design. Copy

linkteller.com

 

[harryS]

Should take a 5.5mm barrel pin used on many chargers.

https://shop.com/products/8579728998592/dc5521-to-junlei-3015-3-pin-e-bike-charging-adapter