Search results

Sweet, that is a nice surprise.

Just turn off the display and then back on. Odometer resets every time, which is quite annoying.

5/18, PO# 730xx, received 8/5, white ST. Canadian order. Bent chainring, and front brake rotor. Otherwise in good shape, but still rideable.

Just cancel and get your money back, it is not worth getting so upset over this. I ordered on May 18th also and waiting for mine. With the state of the supply chain and oversee shipping, I was prepared to wait, it was well known the wait is long. I am not too worried about the $10 or whatever...

If you are scheduled next week, it will be slower if you expedite your order.

A fully charged 48v pack will be around 54.8 volt. 40 volt is when the Battery Management System (BMS) cuts off the power to prevent damage to the battery cells. However, a full discharge like that is stressful to the battery cells and is not recommended. Doing so repeatedly will reduce the...

Is yours an upgrade order?

I will take a look if there is specification stamped on the rotor. Thanks.

I hope the recording is clear. At about 14 seconds mark I applied the front brakes, and you can hear the sound I was referring to. A couple of seconds later there is some additional sound that I have also heard before, but not always there. https://youtube.com/shorts/UalK9clawK0?feature=share

Yeah, we brought ours at a LBS, but we have moved and it is now 1.5 hours away. May still call them and see what they say, but a bit of a pain to bring it in. The brakes were fine for the first 1000 km, stops well and quiet, now it makes this funny noise, but still stops strong.

I will give it a try, although a bit worried applying front brake with left hand while holding camera with right hand. Will post if I get it right. Thanks.

Sorry for the cross post, I originally posted in the Maintenance and Repair sub-forum but no response there yet, hope someone here can help. We have an Aventon Pace 500 with Tektro HD-E350 brakes. We have close to 1100 km on the bike. The bike started to develop a noise that sounds just like...

We have an Aventon Pace 500 with Tektro HD-E350 brakes. We have close to 1100 km on the bike. The bike started to develop a noise that sounds just like the freewheel when you coast without peddling, but a bit louder, when I use the front brake after it past the 1000 km mark. I thought the...

I have tried similar mirrors to those you listed, my opinion on the bar end type mirrors is that they are too far away from your eyes, making the images too small to be useful especially if the mirror is curved. I find the mirror that sits up like the Hafny, with low amount of curves work the...

They do have that. They also published a blog post a few weeks ago about this very topic. https://www.aventon.com/blogs/aventon_bikes/ebike-components-update

They are shipping 2.0 for those that did the upgrade from 1.0, in the order of original PO#. They sent an general email about 2-3 weeks additional delay in shipment last week to everyone waiting for their bikes. I am order 730xx, they told me last week they expect to issue shipping label in...

Did you get your tire patched? Seem to recall you got a big hole in the tire shortly after you got the bike

My home insurance covers ebikes... but... only if the bike is rated 500W or less, and go no faster than 32 km/h (20 mph). Which means Lectric XP, and our Aventon Pace 500 is out of luck most likely. Got to read those fine prints!

I had this Toyota Echo a few years ago. One time late at night at the casino parking lot, I unlocked the door to my car, sat in and about to turn the key in the ignition when I realized something looked different in the car. I had gotten into someone else's car that is same make and color. I...

What you said is true, but programming of the controller determines how much pedal rotation is required. On our Aventon Pace 500, it has a 12 magnets cadence sensor, and it take takes about 1/4 to 1/3 rotation of the crank to engage the motor. The number of magnets determine the minimum amount...