Has anyone mounted a mini tire pump on the bottle cage mount? I have several pumps and non of them fit. Either the mounting bracket is wrong (curved) or the pump hits the frame. It seems the down tube is too wide and the seat tube mounting is too low. I did have a pump mounted on another bike on a wide down tube and the pump ended up scratching the paint since part of the pump was against the frame. I don't want to do this to this new bike at this time. I also don't want to use CO2 cartridges. Presently, I am using a backpack but once I did forget my backpack with the pump in it. My saddle bag has a 6 inch depth so most pumps will not fit in there. If you know of a pump that you have mounted on your bike, could you provide a link for that pump? Thank you.
Creo Tire Pump
- Thread starter mmwada
- Start date
Stefan Mikes
Gravel e-biker
- Region
- Europe
- City
- Mazovia, PL
Both sets of bosses on Creo are intended to either mount water-bottle-cages or install the Range Extender on the seat-tube bosses.
The gravel cyclists I often ride with use similar bosses strictly for water bottles on their traditional gravel bikes, and all of them carry mini-pumps in the back pockets of their jerseys.
rayray
Well-Known Member
- Region
- USA
I bought this for my Creo, and it works perfectly. It holds both the bottle cage and the pump holder.
www.wolftoothcomponents.com
B-RAD Bottle Shift
Bottle Shift can be used to offset a bottle or other accessory to an optimal location. Most commonly used for smaller, curved or dual suspension frames On many full suspension bikes, the water bottle is difficult to access because of interference with the top tube or shock. By shifting the...
www.wolftoothcomponents.com
Thanks, that looks like a viable solution. I am assuming there is no interference concerns when mounting shoe into pedal? I was wondering if you could post a few pictures of pump and water bottle on bracket? Might even make removing the water bottle easier.I bought this for my Creo, and it works perfectly. It holds both the bottle cage and the pump holder.
B-RAD Bottle Shift
Bottle Shift can be used to offset a bottle or other accessory to an optimal location. Most commonly used for smaller, curved or dual suspension frames On many full suspension bikes, the water bottle is difficult to access because of interference with the top tube or shock. By shifting the...
rayray
Well-Known Member
- Region
- USA
I can’t get a picture now, as I’m not home. I installed it so the bottle holder is in its normal (centered) position, and the pump is shifted to the right. It’s not in my way at all.
I suppose you could try moving the bottle cage to the right, but I think that would be in the way. I didn’t try it.
Edit: It occurred to me that you might be able to shift both slightly off center. I’ll play with it when I get home to see if that works.
I suppose you could try moving the bottle cage to the right, but I think that would be in the way. I didn’t try it.
Edit: It occurred to me that you might be able to shift both slightly off center. I’ll play with it when I get home to see if that works.
rayray
Well-Known Member
- Region
- USA
Well, that was fast! I still owed you a picture.
mschwett
Well-Known Member
- Region
- USA
Amazon had the item at the same price along with overnight shipping. No problem with the picture. I was confident that it would work for me but just wanted the extra assurance with a picture. Thanks again. I would never have thought of this and would still be struggling finding a pump that might work.
@mmwada any issue with the water bottle being offcentered with this mount? It doesn't stick out too far to interfere with legs, does it?
BTW - could someone tell me the circumference of the Creo downtube? I don't yet have my Creo but want to get some paint protection film ordered in an appropriate width for the downtube. Thanks!
BTW - could someone tell me the circumference of the Creo downtube? I don't yet have my Creo but want to get some paint protection film ordered in an appropriate width for the downtube. Thanks!
Saratoga Dave
Well-Known Member
Ten inches on mine, the aluminum one. I expect the carbon is the same.
Dazmanturbo
Well-Known Member
The best pump I have found to take on rides is SKS Airboy XL. This pump is 7" and fits easy in a pocket, but does also come with frame mount for cage mounting. The main advantage of this pump is 2 air chambers. The pump is effectively in 2 halves, each half being a compression chamber. Goes up to 80psi in large volume, prefect for my tubeless. Clever design the work really well
Sorry but I missed the question and might be too late for a reply. I have the water bottle cage off center and there is no interference at all. I have a medium frame so it also makes removing the water bottle easier. I believe it is setup where the top of the water bottle is at a slight angle out from the bottom.
I very seldom have experienced a flat tire and so I take two CO2 cartridges for flats. I know I am going to need to deflate the tubes when I get home and use a floor pump to re-inflate them but that is not a big deal. If I was doing a multi-day tours with no sag wagon it would be a different matter.
Similar threads
