bafang

Hello All I am in the process of modifying and machining CUSTOM G062 Hub Motor. Today I am making the shaft and I want to make the laminated core. I have my core out but my windings are still ok so I really don't wan't to destroy it until I burn it up. Then I will rewind it. I am would...

Hi all, Curious situation; The bike of my partner doesn’t seem to give power anymore to the pedals when she is riding it. No clear reasons why this suddenly happens. Discovery; - display turns on, gives the correct speed. Sensor is working. - walk assist does work powerful, so motor is...

Hi, I am trying to get a custom frame built for a Bafang M510 or M560. I'm designing this bike for many purposes, including remote touring, mountain biking, and commuting. My goal is to have as wide a range of gearing as reasonably possible. The bike should be comfortable to ride with no motor...

Hi, I am trying to build up a bike with a Bafang M510 or M560, including a custom battery. I have some uncertaintly how battery SOC reporting works for these motors. For Bafang batteries, my understanding is that SOC is tracked by the BMS using coulomb counting and reported to the motor...

Has anyone found a setting that works well for mountain biking with this engine? I mean like the torque setting, keep current etc etc. Using the bafang USB Cable and the bafang torque software, i want the engine to work at its full potential when the PAS setting is on 5. What settings do i need...

Dear Bafang fans Would you like to set or tune motor controller parameters? K1 Flash is compatible with all Bafang CAN bus motors (5 pin connector with "house" shape). Also can update motor firmware for M500, M510, M560, M600, M620 and M820 motors and run rotor Calibration. Simple as 1, 2 ,3...

Has anyone added a thumb throttle to this engine? Ive got a MM 330.250 15 engine (Bafang mid drive m400) And im wondering if i add a UART PLUG 1T4, would i then be a ble to add a throttle? Or does it require some coding or ?

Hello, I recently replaced my 2-years old BBSHD with new one (wich I planned to use on another bicycle). And immediately feel what I need almost double the current to ride at the same speed. I tested and new and old bbshd on the same road: Eggrider screen. Same settings are programmed on both...

Hi, I just bought my second BBS02B 750W and this one has a quite high resistance compared to my first one with now 1000 Km on the clock. I remember the resistance of my first one was also higher at the beginning so I could live with that for now. The thing is, that my new one never reaches 0...

Hi! Greetings from beyond the Great Water! I don't speak your language fluently, so you have to guess what Google Translate means 😉 I have a Bafang BBS02B (48V, 750W) with a 48V battery (13s6p, 17.6Ah, charged 54.6V). My bike has 26 ”wheels, 2.5” tires, front sprocket 32t, rear is IGH...

Hello. I'm selling a 100% unused, uninstalled Bafang BBSHD Mid Drive Ebike Kit with several additional upgrades and accessories. This is the "Hot Rod" version from Luna Cycles. This will only fit bikes with a bottom bracket size of 68mm (the most common for road and mtb). This will not fit on...

Hello Orbea Katu E50 owner. Great bike - loads of cargo space. But struggling with the app never connecting and want to get the maximum assist out of the motor. Bafang FW C31 250 is the marking on the motor. It comes with Ebikemotion's IWOC control. Any ideas - tips or best places on this...

Hi Everyone, I just purchased and received a Luna Apollo with the Bafang Ultra motor. The programming is pretty horrible on it and I was hoping to make adjustments to the torque. It has a huge delay when pushing the throttle and when it does kick in, it slaps pretty hard. I would like to...

I have a rear hub drive fat bike. I believe 500w. The display is a C600E. The buttons are broken. It appears to have a male green plug and a direct wire to the control buttons. It looks like most displays like the DPC18, 750C or 850C have female green plugs. Is the C600E replaceable with an...

Hi, I'm picking up a new bike today that I'm planning to turn into an Ebike in the next few weeks. It's a Felt Nebula Cruiser 3-speed. I've included a picture of the bike and a link below to some of the spec. This will be my first conversion and I'm brand new to this so I'm interested to hear...

This isnt going to get a lot of press but I wanted to share that we have launched Watt Wagons labs (https://wattwagons.com/collections/labs) The goal is to push the boundaries of performance and be transparent about what you get with the products. To that end, we are launching 1. Bafang Ultra...

Hey folks, I’m new and just accidently posted this same thread in Rules and Etiquette, sorry! I’ve had a couple ebikes and they don’t really ever feel comfortable (I’m 5’7). Current bike is 2018 RadCity 16” so it’s pretty good fit but I just don’t like the geometry. Recently, I saw the Zooz BMX...

I came across a bike called Steiner Ultra E bike online on two different sites below https://www.orangebc.com/de/produkte/fat-e-bikes/steinerdesign-ultra-ebike-fully-27-5-plus-rohloff-gates-karbon-riemen-speed-pedelec-zulassung.html https://www.steinerdesign.net/produkte/bikes Apparently both...

Hello everyone, I have a silly question: is the pedal assist sensor integrated inside bafang mid drives? I’m considering getting a bafang after 3 years using a 1000 W rear hub and im a bit tired of pedaling so hard when the battery dies... I have seen a few videos and they all seem to require...

Solved on July 10th : as WilliamT suggested, it was most likely caused by the motor mounting bracket rubbing against the chassis, due to the mounting nut being slightly loose, or the motor having slightly dropped since first install. At least I reckon. In any case, if you hear the same noise...