Recent content by Nvreloader

Ped Thanks for that tip, I cleaned the inside of the stem, but didn't put any silicone on the valve core...........oops. Tia

This is what I now use, so far with and have had no problems. I use Flat Out (Sportsman series) and HD tubes on my Warthog MD 740 with 26" x 4.80" and the Biktrix Juggs 4 Ultra with 26"x 3" fat tire bikes that are ridden off road, cross country on cow and wild horse trails, with 4800+ miles...

Thanks Guys Gio, My BCD is 130 mm and does have a Dual Shield on each side of the chain ring gear. I don't know if that Dual shield makes any difference. Tia

This is the air pump I used on all my bikes, I have adapted the plug to fit all my (2-52v and 4-48v) E-bike battery's connection points, with Hailong flat bladed pins. https://www.amazon.com/gp/product/B0986MWSFX/ref=ox_sc_saved_title_6?smid=A1I0M5B37LZH6O&psc=1 I also carry enough C 02...

Guys I have the following gears and chain ring set up, (counted). 9 sp x11x34 with a 44t chain ring, with the wide/narrow spacing. A top speed of 7/8 mph while in the 34t using eco 1 step power setting, pedaling or minimum throttle usage. I use this gear selection for 95% of my trail...

Gio It is a stock set up from Biltrix, I'll have to look it up to be sure...... Tia

Gio I only use PAS step Eco 1 95% of the time, I am not into speed, I like slow and slower LOL I would like to get a bit slower, BUT I don't want the hurt my motor or bike.......

Gio I didn't get all of your quote posted, you said, "What is a Bafang 1000 mid drive? There is no Bafang 1000 model number. BBSHD? OEM motor or DIY kit motor"? I was attempting to reply to your question, that per Biktrix, they have listed a 1000W motor....... In using my lowest gear, my top...

I have a Juggs 4 Ultra 1000w (UART motor, torque), See info here: https://www.biktrix.ca/products/juggernaut-ultra-duo-4-step-thru?variant=42192348348613. This is my trail riding/hunting bike, that I like very much, it's a hand full, but it needs to be slower in speed sometimes, in the very...

Merlin A question for you, Would this 3-9 IGH work with a trail riding bike, ie cross country, heavy load application like a trailer being pulled via a Ultra 620 motor, on a narrow cow/horse trail? Think Hunting Bike.....Low and slow....I don't need speed, just the bottom end grunt power. Tia

Black Hand, Thanks for the Squatch's, I really like the family one, the tuffs in each side of the head, show the gender? 3 on the right side are female and 2 tuffs on the left are male, not sure what the baby is?? Tia

UPDATE Well, I changed the Bungee cord length to 8' x 1/4" dia, instead of the 5' I started with, by changing lengths and getting rid of the 3" "S" hooks, and went with a formed eye, that I could kind'a lock down while testing the number of Bungee cord wraps per side. I can get better tension...

PC Both my bike are mid motors, that was the first thing I checked when buying them, as I had the trailer bug, when buying etc. You would have to have custom made trailer bracket/Bobbins for that hub motor. Tia

PC Here are some photo's, click on photo's for enlargement......... https://ibb.co/t51Mdtz Full view, trailer hooked up in the right side, left side trailer arm is hanging there, unattached. The left side of the trailer attachment arm has the inner tube/Bungee sway control attached for testing...

PC Yep, Done finished the trailer attachment brackets. Had to make them for the bikes, as the usual way is to have the Trailer Attachment Bobbins threaded on the end of the solid 1 pc axle, that wouldn't work on these bikes, as the Bobbins would interfere with the derailleurs shifting pattern...