Menu
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Ebike Reviews
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
EMGX's latest activity
E
EMGX
reacted to
PedalUma's post
in the thread
Clean Custom Conversions
with
Love
.
I set my mid-drives to go into a 30% power limp mode until the internal temp goes under 100C. I do not know anyone who has done that...
Sep 15, 2026
E
EMGX
replied to the thread
Clean Custom Conversions
.
The low available gearing with this bike, ~16 gear inches, makes up for lower power. I don't mind climbing slowly on steep hills, it...
Sep 15, 2026
E
EMGX
reacted to
PedalUma's post
in the thread
Clean Custom Conversions
with
Like
.
Some cadence sensor bikes can be programed in about 20 ways. I make them start at 1 volt, without delay, or lag, and I take the overrun...
Sep 15, 2026
E
EMGX
replied to the thread
Clean Custom Conversions
.
Yes controller is in motor. It is lower power compared to my mid drives TSDZ2 and Yamaha at 35nm but retaining the original drive train...
Sep 15, 2026
E
EMGX
reacted to
PedalUma's post
in the thread
Clean Custom Conversions
with
Like
.
@EMXG, Is the controller inside the motor. Very clean. Nice work.
Sep 15, 2026
E
EMGX
replied to the thread
Clean Custom Conversions
.
Under "clean (and easy) conversions" I doubt if anything current comes close to Keyde hub motors. Simply swap in the wheel, single wire...
Sep 15, 2026
E
EMGX
replied to the thread
Bosch Hub Line
.
Keyde has sold a hub motor that sounds almost identical for years. P110 with built in cadence/speed/inclinometer 45nm 36v 250w/750max...
Sep 11, 2026
E
EMGX
replied to the thread
REVIEW: QR-E 250W ELECTRIC BOOSTER BICYCLE MOTOR AND B60i AND B70 BATTERY
.
Thanks but it's not worth my time to pursue, let alone cost of shipping even if Qiroll was willing.
Sep 8, 2026
E
EMGX
reacted to
3dxl's post
in the thread
REVIEW: QR-E 250W ELECTRIC BOOSTER BICYCLE MOTOR AND B60i AND B70 BATTERY
with
Like
.
Well, have to live up to the jet sound if you wanted to continue using it unless you can send to Qiroll for engineer inspection. I'm...
Sep 8, 2026
E
EMGX
replied to the thread
Kickstand Alternative ( YES ! )
.
I picked up a tool hook today and looked around the garage for bits to make a more compact stand than my folding cane or a trekking...
Sep 7, 2026
E
EMGX
reacted to
PCeBiker's post
in the thread
HF Spring Clamps Instead of "Handle Bar Tripods"
with
Like
.
They used to cost $79 on Amazon four years ago. I said F-that, and made my own out of 2x4's and a hole saw. I just revamped them last...
Sep 7, 2026
E
EMGX
reacted to
PCeBiker's post
in the thread
HF Spring Clamps Instead of "Handle Bar Tripods"
with
Like
.
OK, that makes sense 👍👍 I'll bet it was your rear brake? Bubbles tend to rise up the brake line, then end up in the reservoir, but the...
Sep 7, 2026
E
EMGX
reacted to
PCeBiker's post
in the thread
HF Spring Clamps Instead of "Handle Bar Tripods"
with
Like
.
The same sorta thing happened to my car in the 80's. My car ran like crap in the morning on the way to school, but always ran fine on...
Sep 7, 2026
E
EMGX
reacted to
6zfshdb's post
in the thread
How do you draw down a battery for long storage?
with
Like
.
The XP Lite battery uses a simple spade connector. Buy a cheap extension cord, split the plug in half and insert the spades into the...
Sep 7, 2026
E
EMGX
reacted to
PCeBiker's post
in the thread
How do you draw down a battery for long storage?
with
Like
.
I made a battery discharger using three 100 watt incandescent lightbulbs after hearing about it from @6zfshdb ,.. The three bulbs are...
Sep 7, 2026
Members
We use cookies to ensure that we give you the best experience on our website.
Accept
Learn More…
Back