Recent content by Boosted

Big difference between 18km hill climb and 18km ride with 1km hill climb. You might be okay then. Even still a 36km round trip is a lot to ask from a 520 w/h battery. You can use the grin sim to help estimate range with your setup but I still am not sure you could make the commute on a battery...

I would worry less about the discharge and more about the capacity. If you have a 10AH battery for example with a 30a BMS that means it will run full power for 20 minutes. If you are going 30 kmh up this steep hill you are only going to make it 10km before you are out of battery. To add to that...

I just checked my alibaba history. They got me a 10k thermistor as I requested, but I just got it with whatever phase cable they had. And swapped it out. I paid 140 shipped pre tariffs.

Yeah its easy to put in the dimensions on grin spoke calculator Probably not a bad idea to screenshot the L1019 wiring diagram from grins website and send it to them, in hopes that its wired the exact same. OEM L1019 wiring should be adequate if you are only running 90 phase amps around the...

Yeah that sounds great. Unless you are planning to ride up super steep hills or run more than 4-5kw of power, the QS159.8 would be a great option. I think I ordered mine with a L1019 but just swapped it out for the larger 4mm2 L1019 anyways. Plus added statorade while I had it open. Make sure...

1. Yeah I dont know much about the G063's I havent had one. When I saw pictures the copper fill didnt look as good as the G062's but who knows. The G063 is usually a lower turn motor than the G062 from what I have seen. And again the L1121 seems to be less compatible with controllers last I...

45A controller at 48v is 2200w and 60v 45a is 2700w, sounds like we are on the same page. Most kits from CHINA (OEM kits) do not supply 45a controllers with this motor, around 30-35A is as high as they go. I think theres a reason for that. Deep snow, deep sand, steep hills you can definitely...

Yes I believe thats the same seller that I purchased from I think the 12000w and 1500w are the same motor. Ive seen this thing listed both ways. Also its rated 48-60v so that could be the reasoning. But not 100% sure. Phase wires. When I ordered, I asked for an L1019 connector. This is...

I havent ran G062's in a while and have moved on to different motors. My conclusion is its a great motor for low powered setups, but pushing the power limits on this motor just has too many issues. Hard to fit larger phase wires. The windings have limits. No temp sensor OEM. And most importantly...

I did get several M14 axle G062.750's (6.5T) from Risun Motor. Not sure what their current stock is. If this is important to you I would ask the seller if axle measurements are 10x12 or 10x14 for clarification. I havent looked in like a year, but last time I looked you cannot find L1121 cables...

How is it!? The phaserunner should work good as a FOC controller for it, and has plenty of ERPM. My only concern would be the L1019 wiring of the OEM motor. Curious to see how it worked for ya?

Thermistor - yes exactly. Some controllers that have phase speed sensing will still give you a speed readout even without the speed wire, you just wont get the speed readout when OFF the throttle (because its freewheeling). What fails first - It depends. If you run 90+ phase amps (say you run...

60-75 phase amps I would consider the limit for "safe". You can run more, just when going beyond that number the chance you have motor issues starts to increase. The gears, the parallel key, and the heat itself from the motor, a "warm" motor can overheat and melt the windings in as little as 30...

I would not try this project. You will need to machine the stator to fit more wire. I would not recommend a higher gauge wire, I would recommend .5mm wire and just more of them, like 25 strands instead of 15 strands. Machining the stator can damage the laminations in several ways, they can...

The good: - Large high torque stator - The motor seems to take heat well, seemingly outperforming the G062- I was able to run 90 phase amps at low RPM (thick sand) non stop for 2+ miles (several minutes) on a warmed up motor - Steel/Nylon gears from the factory - Much stronger cluch/drive key...