Search results

Here's a Video About VESC. Things to think about.

The high power top top quality VESC like the Tronix 250 R cats me $250. If you don't want that much power there are lower power VESC that are much cheaper. https://flipsky.net/products/torque-esc-vesc-%c2%ae-bldc-electronic-speed-controller The second thing is just because some vesc can push...

It's time to get started. The VESC is looking really good. It is super high quality. You can tell it is built to put out some power. For now I have a test bench set up to get everything hooked up and tested. I have to make the heatsink for the Tronix 250R but anyway my rear rack holding my...

Alrighty, here we go again. More and more of my parts are showing up so I keep shifting gears a bit. Eventually I will get the Stock Bafang Control Working with the Eggrider. I planned to use this VESC in the end so rather than wasting more time on the stock controller that I only want working...

Thats half my troubles. I bought the Motor separate. So now everything else I gotta buy separate. And I am not having a lot of luck finding g062-1000 parts.

I bought the real G062-1000W. It has the fatter Rotor. My rotor is roughly 41 mm Wide.

I just ordered a spool of 8 gage silicon for phase wires and for battery wires. The VESC I bought has 5mm bullet connectors for the phase leads so I only have to solder on the bullets. I bought a 300W Iron today just for the 8 ga wire. The thing is to run 8 gage phase leads off the motor the...

There is still plenty more to come. I just dropped a pile on cables and 8GA Silicon Wire plus everything to make our own connectors. So I will go over all that as well. If your gonna upgrade to run lots of power the wiring needs the capability of handling it.

This is the controller information. YLLSF for Bafang G062 hub motor 48V 30A 1000W controller UART, G062 1KW *Used to replace electric bike part for G062 series motors *design for bafang Motor Controller 48V 1000W ,750W (option) *easy to use and install,1000W /750W power support ，good...

Your welcome. I figured it would be nice to dive deep into this project and get all the highly technical info out here. The controller is brand new so there is nothing wrong with it. It normally would not be able to connect to the Eggrider because the cables out there are not plug and play in...

So generally everything went very well. These are the connections to the board. GND = GND 48V = B+ TX = TX RX = RX POWER LOCK = VK+ The eggrider powers up connects to Bluetooth and displays the right information. The control is powered on. Bafang Protocol is automatically found and paired. I...

Well good news is that it was the right wire. So all the wires are connected now. I'm getting a fault but the eggrider did seem to automatically choose bafang as the protocol so I believe it's communicating ok. I probably need to get the brake throttle and pas hooked up and then maybe it wont...

I'm pretty sure it's got to connect to VK+. You can see that in the picture the VK+. The board has 3 V markings. VB+ VB- = Volts Battery. So hopefully this one marked V is 48 volts or else i am about to fry this thing. But looking at all the wires that go to the stock controller plug you can...

Ok so heres where im at. I got the Eggrider connected. And It turns on just fine. But there is no communication because the controller is not turned on yet because i do not have Power Lock wire connected. I'm not quite sure where to connect it. With the controller plugged in some of the traces...

Alright I got my eggrider today. Which is not compatible with the controller I bought. Eggrider said the controller is not compatible. I believe it is not plug and play but If you make your own cable or solder to the controller board I think it will work. The connections are marked on the...

Yea money. I've dumped a lot of it lately. I like the Bafang. From what I see the quality is pretty good. Far as I know direct drive hubs are a lot bigger. Anyway I have the Bafang and I have the controller + a Eggrider and also I have a Tronix 250R VESC on the way. It is supposed to put out a...

Yea Idk. One time i was not logged in and it said something about sales and contacting the poster and that you couldnt make comments. Just confused me. But I did start another thread with the bafang G062 Info and models and such.

This is the gear size that is in the G062-1000W. It is a little thinner but it would work. Any gears to this specification will fit. The Modulus is 1.25 and 36 teeth. https://www.huco.com/shop/power-transmission/gears/spur-gears/22603600...

These are the gears I ordered. I think there a good replacement. They should be a direct drop in. I'm pretty sure. I have to measure the stock gears when I get home. I'm at a memorial day picnic right now. But I did already order 2 sets of these. It takes a couple weeks to get here. Nope its...

So lets talk about the gears. The drive gear on the rotor is 18T. The 3 spur gears on the clutch are 36T The Large gear in the Wheel Hub is 90T The overall gear ratio is 5:1. The motor makes 5 revolutions per 1 revolution of the Wheel. I am shifting gears....LOL and switching to model the...