Search results

R&R the rear wheel with Lectric replacement. It was a complete rear wheel assembly. Rotor, cassette, and washers and nuts installed. Couldn't be easier. 👍 to Lectric. I do wish the spokes pulled square to the nipples better. Maybe 10 spokes noticably pulling out of square. I have laced a few...

4th ebike... 2nd Lectric. They have been the best to deal with on every level. After 10 + years of ebikes, all brutalized, 1st broke spoke. Wheel to be in today.... but FedEx shows delayed in Nashville. About 25 miles from the house.

I worked in failure analysis for some major manufacturers. Field scraping was typical if it was not a wide spread issue, or if the issue was understood and no more samples were required. I will be concerned for sometime about this bike. I was well paid to examine all "What if" scenarios...

I I agree.

Well, emailed Lectric. They have told me they have sent me an entire rear wheel assembly. They are not interested in my rear wheel being returned. So is this good or bad. Within 48 hours of me sending an email requesting support they have issued a tracking number for a wheel assembly and don't...

There is one particular trail I take to begin a deep woods trek to a hunting area. The trail begins off a field and is thick, uphill, with undulating terrain. I cannot pedal but walk mode is quite valuable. It is a Juiced RCS. I believe the walk mode is initiated via the (-) button.

I wish I could help. My time is geared towards machine automation. Once a board was suspected I would R&R. I did some board level repair for certain customers who gave me the time. Thanks for your write ups.

Lightly used X-Peak step thru. 20 miles. Going to ride looking for my dog. Walked it back out of garage. Rear wheel rubbing fender. Found broke spoke. This bike has always been in my care or sight. Ridden very gently to date. Makes me wonder how much warp was taken out where a broke spoke...

My first thought is an Xpeak frame set up as a commuter. It sure looks a lot like my Xpeak as far a frame goes.

Rode my Xpeak for the 1st time today. 15 miles total. Torque is adequate for my needs. Seat needs upgrading. I did hit my right toe on the on the tire while turning and pedalling. Too bad. The pedals are used for pegs as much as used for propulsion. So I must be careful. Some things I would...

Juiced RCS. Service after sale after warranty. Juiced was zero help when I needed a new motor. Even with the serial number the tech group could not tell me what motor I had. They were condescending, arrogant, and lacked compassion. My probs were not their probs. So Service and support.

It looks to measure .2×.2×.4 (inches) or 5x5x10 (mm)

This what your looking for?

I have walked about 1 to 1.5 miles every day the last almost three weeks with little or no pain. That is a 1st in maybe 15 years. I decided it was now or never.

Good Luck. Please up date. IMO, they should check and ship another along with a return shipping label. That would allow them to trouble shoot it. Was box in pretty good shape?

For front end wobble. I know of one fix to air up tires and dial the front suspension stiffer. I think Lectric should address via email to all owners. If it thru out the bike I would expect Lectric to step up and take care of it. Did they offer any checks for you to do? Like PAS level?

My one problem is I cannot ride for another 8 weeks. I had what appears to be successful and effective spinal fusion. Other wise I do not like the front rack. When squeezing between trees it protrudes too far when tire is turned too sharp. I will be installing Evo Brooklyn handlebar/basket...

It appears the handle bar is 31.8mm. Also the handle bar stem is an up/down post somewhat like the seat post. You are unable to change angle. You might get 3 or 4 inches height increase w/o cable extensions with taller handlebars. I measured 42 inches at the grip. Maybe more available. It...

I will check and get back with you

Due to spinal surgery, I supervised the unboxing and final assembly of my new X-Peak. That is a very attractive bike. The white with silver/gun metal gray accents is a good color combination. My wife and son-in-law took it for a spin just before dark. 10 weeks before I get to take it out. There...