Search results

Anyone know if Frey makes the CC in a size small?

I was just getting use to throwing my bike down in the dirt. :cool: How did you replace the rear skewer with the nut? I just came back from my first trail ride only to find when I got back to the parking lot the rear skewer was loose. 👎 I did not have any damage but OMG.

I am needing to replace my charger too. The stock charger gets pretty hot when charging the battery. I even have the Juiced fast charger and it gets crazy hot. Any long term feedback on good alternative chargers.

I am not able to find reviews of people who have compared the stock M620 motor to a 1000 watt ARCHON X1 CONTROLLER upgrade. How much better is the acceleration? If someone could point me to some reviews that would be great. $1,000 for the upgrade is pretty expensive. I have a new Luna X1 750w...

I have been watching the air pressure in the tires over the last 24-48 hours since installing the Tannus liners and have seen drops of 2-3psi on all of the tires. I feel the pressure is compressing the Tannus foam. I hope it stabilizes. My pressure is 20 psi. Depending on where I am riding I...

I tried to mount the problem tire on another rim and it popped the bead. I am now sure the tire is bad it won't hold a bead even with an inner tube. The tire is very loose on the rim. I called Biketiresdirect and they are sending me a replacement tire under warranty.

I have converted the two front two wheels last night with the Tannus Armour setup. I have not reinstalled the wheels on the bikes yet. 2 more wheels to convert. See my comments below. Couple things I have to comment on. First trying to get a simple answer from Tannus support on the inter tube...

I have 26in 2.4-2.8 Kenda Downhill inter tubes. I can set the bead where it pops out and then it pops out in another area of the tire. The sidewall does not feel like it has even pressure pushing the bead out. I have another set of Jumbo Jim tires same as you I will try tomorrow. That tire had...

I have purchased the Tannus system for my Juiced RipCurrent S 26x4.0 tires. I have been unable to get the tires which are new Maxxis Minion FBF tires to seat. I keep getting the tire to blow out at 15 psi. I have watched a lot of Tannus install Youtube videos and others that have done the same...

Many Attempts to get the valve stem to seal have failed. Air keeps coming out. After much debate and discussion with my local bike shop I am not going to go tubeless with these rims. I am going to abandon the tubeless for Tannus Armour system.

I added a second layer of tape and clear Loctite silicone sealer to the rubber of the valve stem. Will let sit for a few hours and try to inflate again. Thanks for the tip.

Using the Stan's valve stems I was unable to get the air tight seal. Air kept leaking past the valve stem. Did a tub test and air bubbles came out between the lock nut and the rim no other air bubbles were observed. I don't think air is leaking into the middle of the rim and pushing air out the...

I wanted to start a thread on my conversion of the RCS to tubeless. I have had Zero flats since riding the RCS and the Kenda Krusade Sport tires with innertubes over the last 2 years. I did have the Tuffy liners inside on both bikes. The first RCS to get converted to tubeless is mine which I...

I purchased a replacement chain from Juiced. $25 plus $5 shipping. You have to use a chain breaker to remove and install the stock chain. I still am using the original chain after checking it was still good. I am not easy on my chain with trail riding. I know when my chain goes I will have a...

I finally got around to testing the front brakes. Stock Star Union brake levers, Star Union dual piston calipers and 203mm rotors the best stopping distance from 15mph was 16ft. With the stock Star Union brake levers, Tektro 4P calipers and the with 203mm rotors the best stopping distance from...

I just finished installing the Bolany ZTZ shocks. Bolany ZTZ shock stanchions are 34mm vs. the KRsec 32mm. Both are 120mm travel. The Bolany shocks performed very well. Went for a 10 mile trail ride today and no clicking noise!

Update on the 48 tooth chainring. It does require me to pedal faster than before. I tested the same drop and was able to make it out the other side with just enough speed. I am now starting to use gears that I would have skipped before. The bike still does 30mph with pedaling.

I am still waiting to hear from Ebay on the KRsec. Yesterday I went ahead and ordered another 120mm shock, Bolany ZTZ. https://www.amazon.com/gp/product/B08CZ9BVZG/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 I will test the shock before cutting the tube this time. Hope this one works...

It looks like these are all the same build just different stickers and colors. I hope to get a response soon from the seller on Ebay. After watching a rebuild video on the air shock I think the extra travel comes from the removal a rubber bottom out spacer. This may explain the cause of the...

I have the 120mm shock with rebound adjustment. The right side shock has been clicking when the fork is fully compressed. I am not sure if this is a defect or normal. Anyone else have a 120mm travel fork?