Search results

I went in the Seven gravel race, and did the 90 klm course.

The 60V Beast also has a lower 28A controller compared to the usual 30A Ultra controller. So more volts and less amps likely also helps efficiency …..and less heat. In theory I prefer your display, but the reality is I ride on eco pas 1 everywhere regardless of wind, terrain, or elevation. So...

They are great tyres, but for this race the bike felt over tyred and draggy for a higher speed and less technical gravel race.

Mine just has the factory Frey/Bafang tune with the CANbus motor.

I have a decent 4 bike rack. Only mine is loaded in these pics.

Thanks Stefan. Good luck for your race.

Thanks. Just do it! I did see a couple of more gravel comps coming up later in the year. I'm sure your used to more seat time than I am, so a continuous four hour ride is probably nothing for you :) I may also enter some single track competitions later this year as well, such as the Dwellingup...

I've owned 3 of the Mark 2's over my lifetime. One was an RS2000 with the 2 litre pinto motor. I rebuilt the motor and the car from the ground up and tracked it for a while. It literally handled like a big go cart and would embarrass bigger hp V8 cars

A friend of mine mentioned he was participating in his first gravel race with his Amflow Pro. I had a look at the courses which varied in distance - 25klm, 49klm, 90klm and 125klm. I entered in the 90klm race with 2025 vertical metres of climbing as I thought this would give the greatest...

These days I drive an AMG C63 which also has 400rwhp but in a heavier package, so a fair bit slower.

This was my S15 engine bay on the day I sold it about 10 years ago……circa 400rwhp. Lost my licence once and then copped a $1,000 fine and 8 demerit points another time so decided it had to go before it was confiscated and crushed…….400rwhp in a circa 1265kg car accelerated well back then.

Have you ever tracked a car?

In the past I used to track my Ford RS2000 and Nissan S15 at my local racetrack. Have to agree with your ranking that was better than sex. 😎 Then I moved onto big boats which was also a lot of fun and an awesome lifestyle. When my daughter started high school we sold it due to us being able to...

I use a setback adapter myself on my carbon EMTB. The adapter was used to stop the saddle rails flexing, which it did. Otherwise the saddle remains in the same position as before the adapter was installed. Pics for attention.

I agree. Risk of damaging the seat tube. One of my e-bikes manufacturer specifically won‘t warranty frame damage caused by seat post racks because of the stress on the seat tube. Doing this is akin to installing a seat post rack depending on the amount of setback and your weight.

I installed the fair bicycle drop best uc saddle clamp on my eMTB. I had a different use purpose in that I wanted to move the saddle further aft (provides up to 27mm rear aft adjustment). Dropper posts generally don’t have a rearward offset like most fixed seat posts and I was on the limit of...

Another option for a water bottle holder. You could mount it on your seat tube. https://www.merlincycles.com/en-au/sks-anywhere-bottle-cage-adapter-with-topcage-195759.html?utm_campaign=googlebase-AU&utm_source=googlebase&utm_medium=shopping&utm_term=Bottle+Cages&ucpo=116883&gQT=2

The Magura caliper runs a 1mm spacer on the fork post mount, so I could just remove that as a starting point. The rear is fine. I think Magura specs the 1 mm spacer for 203mm rotors and its removal for 200mm rotors. I did buy some 220mm MDR-C rotors which I have yet to fit, so I haven’t bothered...

I would just fit them as I doubt you would have any issues. Your upsizing the rotors, so your overall braking performance will be improved. FYI, on my eMTB, the Magura pads sit slightly higher than the MDR-C rotor outer diameter. I discovered this when I had worn the pads down to the backing...

I found them to a far better combo than the original setup. I did buy a bigger rotor for the rear, but it interferes with the nuts from the kick stand mount. So I have to figure out a way to refit the kick stand or lose it all together if I want the larger rotor. Edit - pic of the bike after I...