Search results

You seem to be the only one to have the ability to make a T07 motor better than anything else available yet dont want to share how you accomplish that. Since you are not willing to share, I guess there will never be any way to verify your claims which pretty much nullifies any claims you make...

Most of the "Torque Sensor" parameters seem mostly self explanatory. Too bad its in the 30s and snowing now Im curious as to how you are using the EAssist levels From the wiki EAssist levels work a little differently. Unlike the Pwr levels, these aren’t a power cutoff value as such. With the...

I think we are lucky to even have the wiki. When flashing the display, the software you use is 100% chinese, luckily To7 has a guide which shows what buttons to push. Initially I chose the wrong serial port and saw all sort of chinese gibberish I had no chance of understanding. Finally...

Not sure how what I was trying to say was misinterpreted but oh well. I really dont want a throttle at all on my DM01. I have never used one on my CYC photon. I find a throttle is kindof a requirement for various situations on a BBSHD PAS system as more of a supplement I only put a throttle...

The throttle on the DM01 is super lame (both in response and overall power). I only added a throttle to compensate for the horrible response/delay starting from a stop. The throttle isnt much better and IMHO is effectively useless to compensate for this even in its most aggressive setting...

There is a small gap between motor and downtube of about a mm. On the DM01 there is a bump on the motor for a mounting bolt that hits the downtube first. I will likely ground it down next time I have it apart to get the motor a tad higher. My DM01 is same height as 46t chainring and the wires...

DM01 Update #3 I seem to have gotten my DM01 setup working now. Had to flash new display software. This allows the 'simple' menu changes for things like units (metric/british) and wheel size to be edited and saved. Went on a test ride. With it set to british units (mph), the motor definately...

Could you post a pic of your bushing A california ebike BBSHD suspension brace can be made to work. The attached pic of the brace only isnt the final version (originally used on a BBSHD install, then I tried several things that didnt work so more metal was removed than on the final version)...

You are describing how it 'used to work'. The long press up and down doesnt work anymore. The new SW with the non-advanced settings definately limits PAS speed to 40kmh (about 24mph). Doing the kph-mph trick (set to kmh, wheelsize to 60% does work). Just found how to access advanced menus...

Are you able to get to the advanced menu to change all the things you claim. I just replaced the controller on my DM01 (it had latest release). This was not compatible with my T24 display in that no changes to anything were allowed. They could be changed, just not saved. I just upgraded the...

DM01 Update #2 Well it turns out after spending two hours swapping the CYC with the DM01, no DM01 settings can be saved (not even the simple things like units (metric/british) and wheelsize. They can be changed but they are not saved Very disappointed with ToSeven

DM01 Update #1 I received the two new DM01 controllers yesterday. Kudos to AliExpress getting it to me in 10 days. With the exception of making sure all the wires were ok when bolting the controller back on, replacing the controller was super easy. The old controller SW Version: V06207 (Aug...

Reduced Battery Capacity after 3-4 years I do most of my rides using two EM3EV 52V 17AH(14S,5P 18650) batteries. The first (BATT1) uses 35E cells and was bought in 9/21. The second (BATT2) uses GA cells and was bought in 9/22. I seem to be doing about 6k miles per year between these two...

Im guessing that motor had about 250 miles on it. I dont deny I beat on it but it was using factory settings. I was trying to find its limits and I succeeded :) Many others in discord have reported blown controllers running 30A during hill climbs. Thanks for the positive Ali feedback, I just...

I really do like the T154 display from what I have seen. My setup has the T24 and I like it alot as well (just big enough to read, no bigger). That being said, I think the T154 would be a better fit. Let us know how the new motors work out for you as far as 'advanced' programming. I really...

DM01 Death The DM01 died today and it was a brutal ride home battling 15-20mph headwinds. Dont think I ever got over 13mph and most was around 10mph. Im exhausted today. Lots of time to reflect on life! At the time, I was comfortably cruising about 400-600 watts. The whole ride was pretty...

I think the use case mentioned by Doom1 is the perfect example👍 I have a PAS option on my DIY Grin GMAC hub motor bike. I originally set it up this way due to the torque sensor not working after crossing water puddles (still happens despite sealing all connections across 3 different torque...

It looks like my DM01 died today which was going to be my final ride doing my efficiency comparison with BBSHD. I was cruising comfortably in City Mode (21A max) in assist 3 of 5 consuming about 400 watts when all power was lost. There is a little yellow triangle that show up but no other...

As harryS mentioned, many of the features you say you will be exploring/explaining might not be available in the latest firmware. That being said, perhaps your efforts would be better appreciated if you added to the DM01/DM02 wiki...

More DM01 updates DM01 vs BBSHD throttle compatibility As it turns out, I have a few spare BBSHD throttles which also use a hall sensor so they will work with the BBSHD, just need to swap a few wires. Not sure its worth the effort though. DM01 throttle The DM01 throttle is super lame. Its...