Search results

Now that I have the IGH, the gear shift sensor is definitely useless because now, I can shift without pedalling, which is what I do anyways. When installing the new shifter and cable for the IGH, it was easier to thread the bare cable through the existing cable insulation which meant leaving...

Just did another 9.5 mile ride. Had several motor cut outs only immediately after pausing pedalling to take a turn. Sometimes the motor wouldn't kick back on until I jabbed the throttle. It's entirely possible this is not related to the changes in programming. I have issues with my gear shift...

A 190mm would make me a buyer 👍

Only problem is no fat tires compatibility. Max outer locknut diameter of 148mm

I mean it is lunch time (at least here on the east coast) Suddenly I'm in the mood for sauce

I believe that first page, the basic one with each PAS setting, is how the bike came so I haven't played with any of that yet. As far as using gears, I only have 3 gears (IGH) and I do use them all but when I'm exercising on flat ground it's 3rd gear, PAS1, 16-18mph. I haven't tested voltage of...

In this case it is evenly spaced at 28% step

Just got back from a 10.7 mile ride with the new throttle and pedal assist settings (I left my basic page as is with the exception of changing the low voltage cut off to the highest it could go. Was 40v, now 43v). Bike is definitely so much smoother. There is also more power in PAS1 (I'm...

Beat me to it by 30 minutes 🤣. Just posted this in the news and hot topics section. 👍👍

Just read this. All new 7 speed Kindernay IGH based on their 14 speed model. Swappable shells available in 32 and 36 hole configuration and standard 6 bolt brake disc compatability. 428% gear range with evenly spaced 28% steps More big news is the new trigger shifter mechanism. They have done...

Ok because when I read flash the section to the right with version number says 48v nominal. And my low voltage cutoff on the main page is selectable but only in a range of 43-38v which I know is way too low for a 52v batt. *Edit* I think this will make more sense when I post some pictures of my...

I played with start current. Anything above 5 and I can hear my IGH, chain and tensioner chirp under the strain. Start current at 2 gave me the buttery smooth take off from a stand still I have always wanted. About 90% of the time that I am riding, it is for exercise (doctor's orders), so...

🤣 I was wondering when you were going to chime in. The 28A cut off was a bit disappointing when I first found out about it back in March or whatever but I've since almost forgotten about it. Are you saying that last 2A is what keeps me stuck right on the threshold in of 30+ mph? The firmware...

Yes I do also know the designated assist is at 9 Right now the only setting I think I'm unsure of was the slow-start. It may be a 4 or 5. I'm wondering if there is any harm in a start current of 2 with a slow-start of 7 or even 8

I have jumped around all these thread over the months and forget where they are and thought the other thread and this one were the same one 🤦. My current is locked out at 28A. I'm not allowed to change it. I guess I got that newer controller that's a bit neutered. Throttle start is 11 Throttle...

You have just humbled me sir. Not sure why I didn't think about doing this? Probably because my shop is 35 miles away and I have no means of transporting the bike via car as of yet.

So my throttle start current is now 2 in order to get a smooth start and stop the jerky initial throttle engagement with my IGH but I'm wondering if the throttle ramp up should be brought up further because now it feels very slow. I want the smooth smart but once it's on I'd like a little more...

@Gionnirocket I haven't touched anything on the basic page but I took a bunch of your settings from pedal assist with the exception of a minor tweak to start current. (settings from post 1). I also finally tweaked the throttle down from some stupid high start current, I think it was 50 and...

Awesome story! Very cool bikes!

You two are always available for a good programming query 👍👍