Search results

  1. T

    For sale: Crank Brothers dropper, 500C display, stem for 35mm bar

    Updated February 2, 2024 I'm selling some quality items no longer of use to me. Purchases can be made from my eBay listings. The shipping discounts through eBay are greater than I can obtain elsewhere. Thanks for looking! Crank Brothers Highline 7 - 100 mm dropper with 31.6 mm post (lightly...
  2. T

    Re-greasing the Ultra motor...is it time?

    On the "controller" tab of the dealer version of the X1 Tool, there's a button labeled "detect encoder". I'm almost certain it's for calibrating the rotor magnet. It would spin the motor, so have the back wheel off the ground.
  3. T

    Re-greasing the Ultra motor...is it time?

    That answers my question if the rotor gear is made of harder steel than the "third gear". Seems like it's not. That's unfortunate.
  4. T

    Kindernay observations and few questions for Pushkar

    Pushkar is the owner of Watt Wagons.
  5. T

    Hydra - 52v to 48v

    It can be done with the cracked administrator version of the X1 Tool. The download links have been removed from the programming discussion thread, but I'll try sending it to you through private message.
  6. T

    Bafang Motor's Waterproof Rating?

    I don't have this large hole. Is it where the wires exit? Mine has a block of rubber that the wires pass through.
  7. T

    Bafang Motor's Waterproof Rating?

    BBSHD has spindle seals, M620 does not, so the waterproof rating is variable between models.
  8. T

    Bafang Motor's Waterproof Rating?

    There are some online claims that they are rated IP65. If that was true, I wouldn't find rust and dust in my M620. I personally rate the M620 at IP51. It could be IP65 with some seals on the crank spindle.
  9. T

    Re-greasing the Ultra motor...is it time?

    Does anyone know if the smallest gear (the one pressed on rotor shaft) is harder steel than the adjacent gear? That way, the adjacent gear would be sacrificial as it is cheaper and easier to replace than the rotor.
  10. T

    Re-greasing the Ultra motor...is it time?

    Yikes! The second gear looks very worn. The tooth profile has worn down to a triangle. The sides of the teeth should be curved like the gear beside it. I imagine the center section of the first gear is worn out too. You're looking at a new rotor (the first gear is pressed on) and a new second...
  11. T

    Archon X1 Programming Thread (questions and experiences)

    1.0.12 has the same checksum hash value as 1.0.10 (it's the same file). I don't know why it exists.
  12. T

    Archon X1 Programming Thread (questions and experiences)

    There should be two exe files. Maybe your antivirus deleted one? XTOOL.exe will launch x1Tool_1_0_10.exe and jump past the login. They need to be in the same folder.
  13. T

    Archon X1 Programming Thread (questions and experiences)

    Yes, I just stripped those wires, twisted them together and soldered. These are the P+ (Power positive) and PL (Power Lock) pins which must be connected to enable the controller.
  14. T

    Archon X1 Programming Thread (questions and experiences)

    I have successfully made an X1 programming cable. First you must start with a genuine FTDI FT232R USB to serial adapter. The counterfeit chips cannot be reprogrammed. I purchased this cable. You can also build your own with instructions found elsewhere on the Internet. SparkFun and Adafruit...
  15. T

    Archon X1 Programming Thread (questions and experiences)

    Hello evixone, Thank you immensely for your login bypass crack. It works perfectly. It also passes more virus scanners than the actual X1 Tool! XTOOL.exe virus check results x1Tool_1_0_10.exe virus check results I'm not sure how long those links will be valid for. Edit: The network...
  16. T

    WW 52V Battery Issue

    I've lost another 0.1V off both my packs since my last last post 8 days ago. That's only about 1% according to a chart I found online.
  17. T

    Archon X1 Programming Thread (questions and experiences)

    Both Rico Czernig and Krasnodar Jandrijevic of Innotrace also work at SSP Safety System Products. I'd say Innotrace is a side gig. Innotrace affiliated websites innotrace.de and xembedded.de are dead. I hope they have the decency to make the code public when they completely give up.
  18. T

    WW 52V Battery Issue

    I've only lost 0.3V from my WW 52V battery over the last month. The same for my custom 52V, 20Ah battery with the same BMS. I charge to 80% (55V) for storage because I'm lazy and that's the minimum setting for my charger. My packs would take years to self-discharge to the hardware undervoltage...
  19. T

    Smooth Tune vs. Archon X1

    The X1 can be programmed for near instant pedal assist by setting "sensitive torque level" to zero. This is a pure torque sensing mode that ignores the cadence sensor. The downside is power tops out at 1500W in PAS 3 and above. I'm going to try reintroducing some "sensitivity torque level" to...
Back