Menu
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Ebike Reviews
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Shifty Shane's latest activity
Shifty Shane
reacted to
Gionnirocket's post
in the thread
Lubing an eBike chain
with
Like
.
That's my go to method. If I'm being thorough I lift the entire bike with a hoist... ... the straps make it easy_peasy_Japanese_y...
Today at 7:06 AM
Shifty Shane
reacted to
mrgold35's post
in the thread
Lubing an eBike chain
with
Like
.
My Himiway Cobra Pro with BaFang M620 mid-drive doesn't rotate the chain backwards when I need to clean/lube. I do the lean the +98lbs...
Today at 7:06 AM
Shifty Shane
replied to the thread
Lubing an eBike chain
.
I can lean my bike over on the kickstand until the rear wheel is off the ground, then rotate the pedals. I've also used a ratchet strap...
Today at 6:12 AM
Shifty Shane
reacted to
teskow's post
in the thread
Lubing an eBike chain
with
Like
.
I push my bikes over on the kick stand just enough to raise the rear wheel and prop it up some way. Get creative with a way to hold it...
Today at 5:50 AM
Shifty Shane
replied to the thread
How accurate are distances on e bikes
.
In your controller programming settings, on the "Basic page" where you set the wheel diameter, try changing "SpdMeter Signal" (# of...
Today at 5:47 AM
Shifty Shane
reacted to
Stefan Mikes's post
in the thread
How accurate are distances on e bikes
with
Like
.
This matter has been discussed in EBR Forums for many times. The short answer is: The accuracy of the odometer depends on the Wheel...
Today at 5:25 AM
Shifty Shane
replied to the thread
How accurate are distances on e bikes
.
With my wheel diameter set to 29" (actual is 28.8"), my speedometer and odometer are approximately 97% accurate compared to a GPS speed...
Today at 5:22 AM
Shifty Shane
replied to the thread
Full face helmet for ebike 20-30 mph speed
.
I'm a bit late to the conversation, I got a cheap helmet for free when I purchased my used dual sport motorbike. I liked the looks of it...
Today at 4:48 AM
Shifty Shane
replied to the thread
Bafang DPC-18 Ebike Display Settings
.
I'm extremely late to the conversation, but the DPC-18 with Eco/Sport modes 0-5 correspond to the Bafang programming software assist...
Today at 2:13 AM
Shifty Shane
replied to the thread
Does changing the Display settings
.
Sorry I'm late to this conversation, you're controller programming settings or firmware must be what's preventing you from changing the...
Today at 2:08 AM
Shifty Shane
reacted to
JGcycle's post
in the thread
Hello everyone, I'm new to e-bikes and I appreciate all the shared knowledge available here.
with
Like
.
Welcome to the forum. :)
Yesterday at 9:38 AM
Shifty Shane
replied to the thread
Ultra Tuning: Decoding the Torque Tab's SPD Table
.
I understand what you're saying, I just thought I might as well eliminate any unnecessary variables, whether or not they will have any...
Wednesday at 11:25 PM
Shifty Shane
replied to the thread
Ultra Tuning: Decoding the Pedal Assist Tab
.
I agree that most of the PAS settings would be overridden by the similar torque tab settings, and any cadence assist should be...
Wednesday at 11:13 PM
Shifty Shane
replied to the thread
Ultra Tuning: Decoding the Pedal Assist Tab
.
From what I've read previously, I thought the "slow start mode" was the ramp rate from zero current to the "start current" value. This...
Wednesday at 10:12 PM
Shifty Shane
replied to the thread
Ultra Tuning: Decoding the Torque Tab's SPD Table
.
The RPM's aren't a necessary value, I was just wracking my brain after I measured the true wheel circumference of my 3" x 27.5" tires...
Wednesday at 9:51 PM
Members
We use cookies to ensure that we give you the best experience on our website.
Accept
Learn More…
Back